Maintenance Tips For Labeling Machines

Maintenance Tips For Labeling Machines

Date:Dec 02, 2020

Labeling machines mainly include: self-adhesive labeling machine, sleeve labeling machine, round bottle labeling machine, beer labeling machine, semi-automatic labeling machine, labeling machine, automatic labeling machine, automatic labeling machine, labeling machine , Automatic labeling machine, hot melt adhesive labeling machine. These products can be pasted on flat surfaces, single-sided or multiple-sided pasting of packaging, cylindrical pasting, partial or full-covering cylinder pasting, concave and corner parts pasting, etc. If you want the labeling machine to have a longer life, then we Take good care of the labeling machine and pay attention to the maintenance of the labeling machine. Maintenance tips of labeling machine:

1. Adjustment of pressure brush device

 

The center of the marking brush is aligned with the label and both sides are symmetrical. The marking brush is perpendicular to the surface of the container. The overlapping gap of the pressure brush sweeping the container is: a single pressure brush is 10mm-15mm, and a combined pressure brush is 5mm-10mm. The distance between the cleaning brush and the sponge is 1mm~2mm. Adjustment of the pressure bottle head. The press head should be 20mm lower when there is no bottle than when there is a bottle.

 

2. Adjustment of label box

 

The center line of the label box, the center axis of the label station is tangent to the label paper, and the center axis of the label plate forms a line at three points. Adjust the tangency of the label plate and the label paper (0 distance), and then move the label box closer to 1mm~2mm. The gap between the label paper in the label box and the pressing strips on both sides should be between 0.8mm and 1mm. If the gap is too large, the label paper will be shifted in the label box and oblique marks appear. If the gap is too small, it will cause poor label push. Adjustment of the position of the label-grabbing hook of the label box: the upper and lower, left and right label-grabbing hooks are on the same vertical plane and evenly work hard on the label paper, so the label can be grasped smoothly. Adjustment of the label supply roller: When there is no label, the label pressing plate can be pressed to the front end of the label box and the label near the label hook finger cannot be crushed.

 

3. Adjustment of the bottle inlet star wheel, bottle outlet star wheel, and bottle inlet screw

 

When adjusting the bottle inlet and outlet star wheel and the bottle inlet screw rod, the press head of the standard machine shall prevail. First, adjust the bottle inlet star wheel. When the bottle pressing head just overwhelms the bottle, adjust the bottle inlet star wheel so that the bottle is in the middle of the star wheel groove. Adjustment of the bottle feeding screw: take the bottle feeding star wheel as the standard. When the bottle is in the middle of the groove of the bottle feeding star wheel, adjust the screw rod so that the bottle inlet side of the screw is close to the bottle without displacement. Adjustment of the bottle-out star wheel: When the bottle pressing head is just raised, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel.

 

4. Adjustment of standard station

 

Adjustment of the squeegee and the rubber roller: There should be no gap between the squeegee and the rubber roller in the entire length. If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolt. The adjustment of the rubber roller and the standard plate: the standard plate and the rubber roller are only in contact with each other without any pressure. The gap is too large and there is too much glue on the target plate, causing glue rejection. If the gap is too small and the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target board. Practice has proved that the gap between the standard plate and the rubber roller is between 0.1mm and 0.2mm. It can be achieved by adjusting the bearing seat at the lower part of the rubber roller, and if necessary, adjust the bearing on the upper part of the rubber roller.


Previous: Share The Skills Of Spray Filling Machine Maintenance

Next: China International Pharmaceutical Machinery Expo